Guides
HOWO Leaf Springs, U-Bolts, Hubs and Wheel Bearings: What to Measure Before You Order
What wears in the suspension and wheel ends of Chinese trucks, and what to measure and photograph before ordering leaf springs, U-bolts, hubs and bearings.
- Prepared by
- CAP Parts Team
- Published
- Reading time
- 8 min read
- References
- 5 sources
Key takeaways
A leaf spring is a set of parts: leaf pack, eye bushings, centre bolt, clips, U-bolts, shackles and hangers. Say which one you need, or order the pack together with the small parts that wear with it.
Do not re-use stretched U-bolts, and re-torque after a short run following the maker’s manual; a loose U-bolt is the usual story behind a broken centre bolt.
A leaking hub seal is a stop-and-fix item because oil on the brakes ruins stopping power; replace the seal, do not re-use it, and look at the bearing at the same time.
Wheel hubs and bearings are matched by the axle, not by the truck badge: send the axle plate, the hub flange photo and the bearing number if you can read it.
Measure and photograph first: leaf length and width, eye diameter, number of leaves, hub bolt-circle and bearing marks. Those five items remove most wrong orders.
On this page
Short answer: On Chinese trucks the suspension and wheel ends wear first on rough roads and heavy loads: leaf pack and eye bushings, U-bolts and their seats, hub seals and wheel bearings. Before ordering, identify the axle, count and measure the leaves, photograph the eyes, centre bolt and U-bolt seat, and read the numbers on the hub and bearing. Then send those with the VIN so we can confirm the exact version.
Why this group is easy to order wrong
“Leaf spring” is one name for a whole assembly. A published explainer from the Vietnamese parts maker THACO breaks it into the leaf pack (high-tensile spring steel plates stacked to a set camber), spring eye bushings, a centre bolt with clips, U-bolts and fasteners that clamp the axle to the spring seat, shackles and hangers, and the shock absorbers that sit beside it. An order that says only “HOWO leaf spring” could mean any of these, and a supplier then guesses. Even sellers confuse names: one listing found while researching this guide was titled as a HOWO leaf spring mounting but described a multi-layer rubber and steel plate part, which is a different component. Name the part, then back the name with measurements and photographs.
The second reason is how many versions exist. A truck brand sells tractors, tippers, cargo trucks and mixers with different axle ratings and different spring packs, and the front and rear packs differ. An older HOWO cargo-truck specification sheet lists front and rear leaf springs with shock absorbers and a transverse stabilizer, which is a reminder that a truck has more than one spring position and more than one related part. Our HOWO and Sinotruk page and Shacman page show the truck series we list parts for, and the axles and suspension group shows the part families.
What wears, and where to look
| Position | What wears | Typical sign | What to photograph or measure |
|---|---|---|---|
| Leaf pack | Cracked or broken leaves, lost camber | Truck sits lower on one side, wanders, uneven tyre wear | Side view of the truck on level ground; each leaf end; count of leaves |
| Spring eyes and bushings | Cracked, torn or hardened bushings, worn pins | Clunking, play at the eye | The eye from the side, the pin and bushing after removal, eye inner diameter |
| Centre bolt and clips | Loose or broken centre bolt, missing clips | Leaves shifted sideways, one leaf sticking out | Top view of the pack; the centre bolt head and nut |
| U-bolts and seat | Stretched threads, rust, polished seat marks | Axle moves under the spring, pack shifts | The U-bolt, the nuts, the axle seat and the top plate |
| Shackles and hangers | Worn pin holes, cracked brackets | Rear end sways | Shackle and hanger at both ends of the spring |
| Hub oil seal | Hardened lip, scored contact surface | Oil on the hub face or brake drum | The wet area and the seal OD marking |
| Wheel bearings | Rough running, heat, play | Noise at speed, hot hub, play at the wheel | Bearing marks after removal, hub flange, bolt circle |
THACO’s list of warning signs for springs matches what workshops see: unusual vibration on rough roads, noises from the spring area, bent or broken leaves, the vehicle pulling or wandering, uneven tyre wear, and the truck sitting lower than normal. Any of these means inspect, not “order a spring blind”.
What to measure on a leaf spring
You cannot choose a spring by length alone, but length is the first check. With the spring removed and laid flat, record:
- Overall length of the main leaf, measured in a straight line between the eye centres, and whether the spring has one eye or two.
- Width of the leaves and the thickness of the main leaf.
- Number of leaves, counted from the end face, and whether each leaf has a different length (a stepped pack) or a parabolic profile.
- Eye inner diameter and the width of the eye, plus whether a bushing is fitted.
- Centre-bolt hole position and the distance between the U-bolt holes or the width of the axle seat.
- Front or rear, left or right, and whether it is a first or a second (helper) spring on a rear bogie.
Put a tape in the photograph so the numbers can be checked. If the spring is still on the truck, measure the height of the truck at the wheel arch on level ground before lifting, so we can see how much camber has been lost.
U-bolts: a small part with a big effect
THACO’s breakdown says U-bolts and fasteners clamp the axle to the spring seat and secure the assembly to the chassis. When the clamping is poor, the pack can move on the axle and the centre bolt takes loads it was never meant to carry. Spring makers repeat the same advice: one US spring supplier tells owners to fit the springs with the vehicle’s full weight on the tyres, torque the U-bolts to the specification, and re-torque after a short distance because the assembly settles. Their figures are for US vehicles, so do not copy them onto a Chinese truck; use the truck or spring maker’s manual for the values and the re-check interval.
Practical rules that do not depend on any figure:
- Replace U-bolts when springs are replaced, and when threads are stretched, rusted or damaged. A re-used bolt that has already stretched cannot hold the pack.
- Tighten in a cross pattern, not one side at a time.
- Look for polished marks on the axle seat or top plate, which show movement.
- Check the U-bolt thread size and length before ordering; the length depends on the axle seat and the pack height.
- Keep the right nuts and washers; mixing grades or styles is a common source of loosening.
Wheel hubs and wheel bearings
Hubs and bearings are matched to the axle model, not to the truck badge, so start from the axle plate. On a heavy truck the wheel end contains the hub, an inner and outer bearing, the seal and the brake drum or disc. STEMCO, a wheel-seal maker, explains that the seal keeps lubricant in and keeps dirt out, and that you usually do not know it is damaged until you see oil leaking, hear grinding or feel steering difficulty. Two points from that guide matter when ordering:
- Slight seepage on a newly fitted seal can be pre-lube grease escaping, but dampness well onto the hub face means the seal may be leaking and should be replaced as soon as possible. Leaking lubricant that reaches the brakes impairs stopping ability.
- A seal that has been installed cannot be re-used. If a seal leaks because it was installed badly, fit a new one, not the old one.
For a quote we need the bearing numbers where you can read them. The part list at the end of this guide shows how we list hub and bearing parts. For example, we list a hub bearing unit under part numbers shown on that page and a hub bearing unit with hub assembly; these are examples of what we list, not a claim that either fits your truck. See also the rear hub oil seal.
Orders that go wrong, and how to avoid them
| Mistake | What happens | Fix |
|---|---|---|
| Ordering by “HOWO” alone | A pack for a different axle rating arrives | Send VIN and axle plate photo |
| Ordering only the pack | Old eye bushings or pins ruin the new spring | Order bushings, pins, centre bolt and U-bolts with it |
| Re-using U-bolts | Pack shifts, centre bolt breaks | New U-bolts, torque and re-check per the manual |
| Replacing a leaking seal only | Bearing damage remains | Inspect bearing and hub surface at the same time |
| Mixing left and right, front and rear | Wrong camber or length | Mark the position before removal |
Fleet habits that save money
- Inspect the spring packs, eyes and U-bolts at every service, and the hub area at every walk-around; oil on a hub face is a work order.
- On tippers and mining trucks, look at the spring packs when the body is unloaded and the truck is on level ground; loaded trucks hide a lost camber. Our guide to what wears first on tippers covers the rest of the chassis.
- Keep a record of which side and position was replaced and when. Patterns show quickly: one hub failing repeatedly points to brake drag, a poor seal fit or the wrong bearing adjustment, not bad luck.
- Do not mix very worn and new springs on the same axle without checking the ride height afterwards.
- Plan an axle’s worth of small parts (bushings, pins, U-bolts, hub seals) when the truck is already stripped; labour is the expensive part.
What to send us for a quote
- The VIN, or the chassis plate photo.
- The axle plate photo and the axle model if known.
- For springs: side photo, top photo of the pack, number of leaves, overall length, width and eye diameter, front or rear, left or right.
- For U-bolts: photo of the old bolt and nuts, thread size and the axle seat.
- For hubs and bearings: photo of the hub flange from the outside and inside, the bolt circle, and any numbers printed on the bearing or seal.
- The quantity per truck and how many trucks.
Send these on the quote page or through contact; we confirm the exact version before quoting. If you are still working out what parts your trucks use, read how to identify the truck before ordering and the part-number guide. Choosing between original and aftermarket? See genuine and aftermarket parts.
Truck part groups to look at
Frequently asked questions
- What should I measure to order a HOWO leaf spring?
- Record the overall length between eye centres, leaf width, number of leaves, eye inner diameter, whether it is front or rear and left or right, and the position of the centre bolt. Photograph the pack from the side and the top with a tape beside it, and send the VIN and axle plate photo so we confirm the exact version.
- Can I re-use old U-bolts?
- Not if they are stretched, rusted or have damaged threads. U-bolts clamp the axle to the spring, and a bolt that has already stretched cannot hold the pack. Fit new bolts with the spring and follow the maker’s manual for torque and re-checking.
- Why does the centre bolt of a new spring break?
- Spring makers point to loose clamping: when the U-bolts are not holding the pack, the centre bolt takes loads it was not designed for. Check the U-bolts, the seat and the torque, and look for polished marks showing movement.
- How do I know if a hub seal is leaking?
- Slight seepage on a new seal may be pre-lube grease, but dampness spreading well onto the hub face means a leak. Replace the seal with a new one, never re-use it, and inspect the bearing, because leaking lubricant can reach the brakes.
- Are hubs and wheel bearings the same across HOWO trucks?
- No. They are matched to the axle model and the hub design, not to the badge. Send the axle plate photo, the hub flange photo and the bearing numbers so we confirm the exact version before quoting.
- Should I replace the leaf spring bushings with the spring?
- In most cases yes: worn eye bushings and pins spoil a new pack quickly. Order the bushings, pins, centre bolt and U-bolts together when the truck is already apart.
- Do you list leaf springs for Shacman, FAW and Dongfeng as well?
- We list parts for several Chinese truck makes. Send the VIN and photos for any make and we confirm the exact version; we do not guess a fit from the badge.
Sources
- [1]What Are Truck Leaf Springs? Structure & Maintenance. THACO Industries.
- [2]All About Wheel Seals. STEMCO.
- [3]How To Fix Squeaking Leaf Springs. Eaton Detroit Spring.
- [4]Basic Configurations and Technical Parameters of HOWO Cargo Truck (4x2). cargotruckforsale (blog).
- [5]Sinotruk HOWO spare parts catalog list (seller catalogue). AutofromChina.




