Guides
How to find the right part number for a HOWO or other Chinese truck: parts catalogue guide
How to use a HOWO / Sinotruk parts catalogue, read the number on the old part and cross-check it, plus what to send when you have no number at all.
- Prepared by
- CAP Parts Team
- Published
- Reading time
- 7 min read
- References
- 3 sources
Key takeaways
Start with the truck, not the part: the VIN or chassis number, the engine nameplate and the gearbox and axle plates decide which catalogue page applies.
A parts catalogue (parts book) is organised by groups with a picture and a table of serial number, part number and name; match the picture to your old part, then read the number from the table.
Cross-check: the number in the catalogue, the number on the old part and the number the seller quotes should agree. If they do not, stop and ask.
Third-party catalogue PDFs online are of unknown date and model coverage; treat them as a lead and confirm the final number with your supplier or a dealer against your VIN.
No number and no catalogue? Photos of the old part, the nameplates and the truck are enough for a supplier to identify it.
On this page
- 01What a parts catalogue looks like
- 02Step by step: from truck to part number
- 03Cross-check table
- 04Reading the number on the old part
- 05Catalogue PDFs from the internet
- 06Worked example: from a worn part to a confirmed order
- 07Common mistakes when reading a catalogue
- 08When you have no part number
- 09What to send us for a quote
Short answer: Use the truck’s VIN or chassis number and its engine, gearbox and axle plates to pick the right catalogue, open the group that holds the part (engine, clutch, brakes and so on), match the picture to your old part and read the part number from the table beside it. Then check that number against the one on the old part. If the two differ, or no catalogue is available, send photos and plates and have your supplier confirm the exact version before you order.
What a parts catalogue looks like
A parts catalogue, also called a parts book or parts list, is a set of pages organised by group (engine, fuel system, clutch, gearbox, front axle, rear axle, brakes, electrical, cab). Each page typically has an exploded drawing with position numbers and a table beside it. Public examples show how the tables are laid out. A sample from a HOWO D12 engine catalogue lists “Serial Number” and “Name” with the part number in the row, and the part numbers in it begin with letters such as VG followed by digits. A public list of frequently replaced HOWO parts shows “No.”, “P/N” and “Description” columns, with numbers beginning VG or WG. Both are third-party pages and both say nothing about which truck year they apply to, which is exactly why you should not rely on them without checking.
Note the difference between the position number (the figure on the drawing, only used within that page) and the part number (the one you order with). Mixing them up is a common source of wrong orders.
Step by step: from truck to part number
- Identify the truck. Write down the VIN or chassis number, the model on the plate, the engine type and number, the gearbox and rear-axle types. See how to identify your truck or bus.
- Choose the catalogue that matches. Catalogues are issued for specific models, engines and emission versions. Ask your dealer or supplier which book applies to your chassis number; do not assume that a catalogue for a similar-looking truck applies.
- Find the group. Go to the group that holds the part: for example clutch and gearbox, air brakes or engine.
- Match the drawing to the old part. Compare shape, mounting points, connectors and size against the old part in your hand. Many parts have left and right, front and rear, or long and short variants that look similar on a small drawing.
- Read the number from the table. Write down the part number exactly, including letters, dashes and spaces. Letters at the start of the number are part of it.
- Check for notes. Catalogue rows often carry remarks such as quantity per vehicle, left or right, or a range of chassis or engine numbers. Read them.
- Cross-check with the number on the old part and with the seller (see the table below).
- Send it to the supplier with the VIN and a photo of the old part, and ask for confirmation of the exact version.
Cross-check table
| You have | You check | If it disagrees |
|---|---|---|
| Number in the catalogue | Number printed or cast on the old part | Ask whether the part was replaced earlier with a different one, or whether the catalogue is for another model or year |
| Number on the old part | Number the supplier quotes | Ask the supplier to explain the difference in writing, with photos |
| Catalogue picture | The old part itself (photos with a ruler) | Compare mounting points and ports; send photos before ordering |
| Number quoted by a seller | Your VIN or chassis number | Ask the seller to confirm against your chassis number, not “for HOWO” in general |
Reading the number on the old part
Many parts carry a number: stamped, cast into the body, printed on a label, or laser-marked on a plate. Clean the part gently first, and photograph the face with the markings in good light from at least two angles. Remember that the old part may itself be a replacement, so its number is a clue and not proof that it is what the truck was built with. Also note any engine, gearbox or axle plate number that sits near the part, since catalogues for assemblies are often organised by that type.
Catalogue PDFs from the internet
Searching “HOWO spare parts catalog pdf” returns uploads and trader pages. They can help you see how a part is described and what numbers look like, but their date and the models they cover are not clear, and some show only a few pages as a sample. Use them to prepare the question, not to place an order. If your supplier cannot confirm the part against your chassis number, the risk of a wrong version is yours.
Worked example: from a worn part to a confirmed order
This is a generic example of the method, not a real order. Say a fleet mechanic finds that a brake component on a tractor unit is worn out.
- Record the truck first. He photographs the VIN or chassis plate and stamp, the engine nameplate, and the gearbox and axle plates, and notes the mileage or hours and the load type.
- Remove and clean the part. Before it goes in the scrap bin, he wipes it and photographs it from four sides with a ruler beside it. He photographs the face with any stamped, cast or printed number in good light, and the mounting points.
- Find the group. In the parts book for the chassis he opens the group for the system, here air brakes, and looks for the drawing that matches the old part, including whether it sits on the front or rear axle and on the left or right.
- Write down what the table says: part number, name, quantity per vehicle and any remark. He notes the position number separately.
- Compare with the old part. The number from the book and the number on the part are the same or they are not. If not, he writes that down honestly and sends both.
- Write the inquiry so the supplier can answer in one reply: truck brand and model, VIN or chassis number, the system and position (front or rear, left or right), the number from the catalogue and the number on the old part, quantity, preferred tier (genuine, OEM or aftermarket) and destination country. Attach the photos.
- Read the confirmation. The reply should repeat your part number and VIN and say which tier it is. Check every line against your own notes before you pay.
- After delivery, compare the new part with the old one before fitting: mounting points, ports and size. Keep the packaging until it is fitted and tested.
Following the same eight steps for every part makes later orders faster, because the truck record and numbers are already in your file.
Common mistakes when reading a catalogue
- Using a catalogue for a similar-looking truck of another model, year or emission version.
- Taking the position number from the drawing for the part number.
- Dropping the letters at the start of the number, or changing a letter O into a zero or a letter I into a one when copying by hand.
- Ignoring remarks such as left or right, quantity per vehicle or chassis ranges.
- Matching on the picture alone when the drawing is small and several variants look alike.
- Ordering an assembly when only a repair part is needed, or the opposite, because the catalogue lists both.
- Trusting a number from a seller’s listing without checking it against your VIN.
- Not keeping a record of what was ordered and what arrived, so the same error is repeated next time.
When you have no part number
Many orders start without a number. You can still order: send the information below and let the supplier do the catalogue work against your VIN, plates and photos.
What to send us for a quote
- VIN or chassis number (photo of the plate and the stamped number)
- Engine nameplate, gearbox plate and rear-axle plate (photos)
- Several photos of the old part: front, back, side, and the marked area, with a ruler
- The part number if you have one, and where you read it (catalogue or part)
- Quantity, and whether you want genuine, OEM or aftermarket (see genuine vs OEM vs aftermarket)
Send this through the quote page or contact us. We confirm the exact version for your truck. Brand pages: Sinotruk / HOWO, Shacman, FAW Jiefang.
Truck part groups to look at
Frequently asked questions
- Where can I find a HOWO parts catalogue?
- Dealers and suppliers hold the current parts books for specific models. Third-party PDFs and sample pages circulate online, but their date and model coverage are not clear, so use them as a guide and confirm the final number against your chassis number.
- What does a Sinotruk part number look like?
- In public catalogue excerpts, numbers often begin with letters such as VG or WG followed by digits. This is the format seen in third-party lists, not a rule you can use to decode a number, so confirm any number with your supplier.
- Can I order from a catalogue PDF without the VIN?
- It is risky. Variants differ by model, engine and emission version, and a catalogue page may not say which one applies. Send the VIN or chassis number so the supplier can confirm the exact version.
- The number on my old part does not match the catalogue. What now?
- The old part may be a replacement of another make, or the catalogue may be for a different model or year. Send photos of the part, the number and your plates and ask the supplier to explain the difference before you order.
- What is the difference between a position number and a part number?
- The position number is the figure on the catalogue drawing, used only on that page to link the picture to the table row. The part number is the one you order with.
- How do I find the part number if I only have a photo?
- Send clear photos of the part from several sides with a ruler, plus the truck's VIN and engine nameplate. A supplier can identify the part from the nameplate and photos and confirm the number.
- Is an aftermarket part number the same as the Sinotruk number?
- Not always. Some sellers list the original number together with their own reference. Ask which number the part is sold under and what tier it is.
Sources
- [1]SINOTRUK HOWO D12 Euro-III engine parts catalog sample. China Truck Times.
- [2]SINOTRUK HOWO spare parts catalog list and prices. AutoFromChina.
- [3]Chinese truck parts sourcing guide. DocShipper.






